DIY: Cutting Rear Springmount aka "the springmount mod" - - Infiniti G35 & G37 Forum Discussion | rupromenergo.ru
Show Your Support Become A Premier Member

    > >
  • Reload this Page >
    • DIY: Cutting Rear Springmount aka "the springmount mod"


DIY: Cutting Rear Springmount aka "the springmount mod"

Thread Tools Rating: Thread Rating: 8 votes, 5.00 average.
Old 01-29-2007, 04:08 AM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
DIY: Cutting Rear Springmount aka "the springmount mod"

Since I keep getting PMs about this mod, and I needed to get a couple more MM of clearance in the rear. I decided to purchase a new set up rear springmounts and recut them, taking a little bit less off this time. Credit goes to Gsedan35, who was the first to do this, and Borahatch for giving me tips on how to go about cutting the mounts.
See Gsedan35's DIY on installing springs to remove the rear springmounts.

The pieces look something like this:
Side

Top


Tools:
Hacksaw
Tape
C-Clamp
Vise
WD-40 or similar lubricating spray
Rags

Start by taping a ring around the springmount of exactly how much you want to cut off. How much you cut will be how much more drop you will get so measure accordingly before cutting. I used Duct tape, but anything will work as long as it sticks to the rubber. I don't recommend blue painter's tape, because I used it the first time and it doesn't really stick to the rubber.


Next, get a rag or in my case some disposable gloves and insert into the hollowed out end of the springmount to provide a cushioned area for the C-clamp to seat to. Install the C-Clamp like in the picture and tighten until the springmount is difficult to rotate/move. Make sure to not overclamp or you can crack the plastic.




Insert the C-Clamp into your vise to provide a stable cutting rig


Get out your hacksaw and WD-40 or equiv


Begin by lubricating your hacksaw blade and springmount by spraying WD-40 onto the blade and rubber, and begin sawing along your tapeline. The outer ring of the springmount is rubber, but the inner ring is made of a plastic, so saw through the plastic. Loosen the clamp and rotate the mount 1 notch and retighten and continue sawing until you cut all the way around the mount, being careful to cut as straight and evenly as you can.


Once you finish cutting, you should end up with something that looks like this, they aren't exactly straight, but close enough, I've been running them for 6 months and no problems here


Here is a comparison of the height difference after cutting, ~1/2"


Reinstall in stock location


End up with a even drop! Dropped on 350z Tein H-Techs, but will work with any spring




Be prepared for camber issues in the rear, just like any drop in the rear over 0.4", I installed the SPC rear camber kit as well and will be getting an alignment soon.
The Following 2 Users Say Thank You to redlude97 For This Useful Post:
KnowScott (01-24-2012), nbarkins (11-02-2012)
Old 01-29-2007, 12:01 PM
Calvin's Avatar
Overglorified Altima
iTrader: (65)
Join Date: Jun 2006
location: Chicago
Posts: 53,505
Thanked 179 Times in 122 Posts
now it won't get lost
Old 01-29-2007, 01:52 PM
O HELLA JDM's Avatar
Registered User
iTrader: (49)
Join Date: May 2006
location: San Diego, CA
Posts: 18,874
Thanked 22 Times in 18 Posts
thats a crazy drop... ehh id be too lazy to cut springs...and then i would need a chamber kit....ehh me and my broke ***...but thanks for the DIY
Old 01-29-2007, 02:01 PM
Registered User
iTrader: (9)
Join Date: Jul 2006
location: Pothole Central and still ridin slammed...Boston
Posts: 15,043
Thanked 21 Times in 13 Posts
Nice!
Old 01-29-2007, 03:27 PM
Registered User
Join Date: Mar 2006
location: 630/773
Posts: 456
Thanks: 0
Thanked 1 Time in 1 Post
Quote:
Originally Posted by G35Pinoy
thats a crazy drop... ehh id be too lazy to cut springs...and then i would need a chamber kit....ehh me and my broke ***...but thanks for the DIY
You are NOT cutting the springs, but rather the spring mounts.
Old 01-29-2007, 03:48 PM
Registered User
iTrader: (14)
Join Date: Oct 2005
location: cupertino, CA
Posts: 527
Thanks: 0
Thanked 0 Times in 0 Posts
are you going to sell your precut spring mounts????
Old 01-29-2007, 05:38 PM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
Quote:
Originally Posted by jiggafree
are you going to sell your precut spring mounts????
Actually, I have my first ones for sale, they are the ones that achieved that drop in the pic. I'll post something in the marketplace when I get some pics up.
Old 01-29-2007, 05:39 PM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
Quote:
Originally Posted by G35Pinoy
thats a crazy drop... ehh id be too lazy to cut springs...and then i would need a chamber kit....ehh me and my broke ***...but thanks for the DIY
Its a camber kit, and did you read my post at all? I never once mention cutting the springs
Old 01-29-2007, 05:40 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Join Date: May 2005
location: ɐʍ 'ǝlʇʇɐǝs
Posts: 35,467
Thanked 523 Times in 438 Posts
Gotta love the "two in the pink and one in the stink" hand gesture
Old 01-29-2007, 08:06 PM
Calvin's Avatar
Overglorified Altima
iTrader: (65)
Join Date: Jun 2006
location: Chicago
Posts: 53,505
Thanked 179 Times in 122 Posts
how much do you plan on selling them for? i might get them and sell them as a package deal when i sell my 350z h techs
Old 01-29-2007, 08:12 PM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
I was thinking $50+shipping, basically the cost of a set of new ones, except they come premodified.
Old 02-21-2007, 08:57 PM
GWord256's Avatar
Registered User
Join Date: Dec 2006
location: Cleburne, TX
Posts: 1,010
Thanked 1 Time in 1 Post
That looks easy enough to do. I'd like to drop the front just a tad for a bit more agressive look. Maybe 1/4 to 1/2 inch.

How long would it take to do the springmount mod (e.g. is this a one day/weekend job)? And could any Joe-Schmo do it? I've got some tools and would buy the rest as needed but I never worked on suspension before.
Old 02-21-2007, 10:28 PM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
Quote:
Originally Posted by GWord256
That looks easy enough to do. I'd like to drop the front just a tad for a bit more agressive look. Maybe 1/4 to 1/2 inch.

How long would it take to do the springmount mod (e.g. is this a one day/weekend job)? And could any Joe-Schmo do it? I've got some tools and would buy the rest as needed but I never worked on suspension before.
doesnt work on the front, this is only for the rear
Old 02-22-2007, 12:11 PM
Registered User
iTrader: (7)
Join Date: Mar 2005
location: Tampa, Fl
Posts: 581
Thanks: 0
Thanked 2 Times in 2 Posts
How hard are the springmounts to get out in the first place?
Old 02-22-2007, 02:10 PM
redlude97's Avatar
Registered User
Thread Starter
iTrader: (25)
Join Date: Feb 2006
location: Seattle, WA
Posts: 1,911
Thanks: 0
Thanked 8 Times in 5 Posts
Quote:
Originally Posted by hottysmerf
How hard are the springmounts to get out in the first place?
If you know what you are doing, it takes longer to take the wheels off than to remove the springmounts. I can do it in ~10 mins per side including removing the wheels

Related Topics
Thread Thread Starter Forum Replies Last Post
Dash light problem wonderizm G35 Coupe V35 2003 - 07 8 09-24-2015 04:09 AM
MsFitFern New Members Check In 13 09-07-2015 03:45 AM
FS: 05 G35 Sedan 6MT Diamond Graphite - $7000 derres G35 Cars 3 08-28-2015 04:27 PM


Tags
350z, aim, cracked, cut, diy, g35, mod, mount, rear, removing, rubber, slammed, spring, springmount, springs, suspension
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 11:11 PM.


Copyright ©2002 - 2017, rupromenergo.ru All Rights Reserved. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Related pages


dupli color chrome paintmichelin primacy mxv4 reviewdiscount tire flat repair costmemphis audio 4 channel amphow to remove a rusted rotor2011 nissan altima service engine soonwhat side is bank 2 sensor 22007 kia sorento batterywhat is muffler deletebp gas invigoratedrift rc bodieshow to hook up a bazooka bass tubew body coiloversyakima king joe 3car spraying coolantmitsubishi galant vr4 salehow much does it cost to replace rack and pinioncar stereo mississaugawhere is located the crankshaft position sensor7th gen accord coupeheaders hp gainebc brake rotor240z carpetinfiniti of riversideis250 vs g372006 volvo s60r 0 60how to reset seat belt after airbag deployed2009 g35 specsvalve ticking noiseviper alarm sensitivity adjustmentresonator or mufflersilver plasti dip wheelsgeneral gmax tires reviewgtm motorsportsecheck lorain county ohiorain x latitude bladesvq35detkonig afterburners350z insurancekendall engine oil reviewgrinding noise when driving slowz1 motorsports couponorion hcca 12 inch subwooferweight of infiniti g37rack & pinion steering costjl audio w3v3 12 specsdepo projectorstokyo drift rx7 rimstires featheringbmw 335 forumsmemphis 12 subwoofersinfiniti g35 tire pressuresolar guard tintg37xs vs g37xdoes my car have a timing chain or belt350z rev upwhere is crank sensor locatedsandra wong modelxxr 552phoenix gold zx475tispit fire gtae46 strut tower bracetyre size calculator miataups hayward cahow to wire a subwoofer350z horsepowermegan track coiloversretro projectorpennzoil gearplus 80w 90 gl 4what kind of battery for nissan key fobwho makes plasti diprhino ramps 8000thin wall spark plug socketdiamond plaza rowland heightscar rims visualizerxm navtrafficis am autoparts legitziebart diamond gloss pricejack stand pinch weld adaptertsudo sp2 mufflersti oil catch can install