Headlight lenses faded? Clear Coat Anyone?? - - Infiniti G35 & G37 Forum Discussion | rupromenergo.ru
Show Your Support Become A Premier Member

    > >
  • Reload this Page >
    • Headlight lenses faded? Clear Coat Anyone??


Headlight lenses faded? Clear Coat Anyone??

Thread Tools Rate Thread
Old 06-04-2011, 02:50 AM
sssmasss's Avatar
Registered User
Thread Starter
Join Date: May 2011
Posts: 89
Thanks: 0
Thanked 6 Times in 4 Posts
Headlight lenses faded? Clear Coat Anyone??

I always want to do this but i was not willing to test on my headlight lenses. This guy did. here is is process. I thought guy guys might want to try this. The other method involved wax and buff is only a temporary fix. I had to sand and wax and buff my light every 4 months. not so fun. I hope this will fix the light for atlease a year or two.

here is the process. not done by me..


o with the whole wet sand, polish, and seal, I wanted to try something a little different that would last longer with less maintenance. I opted to apply a “clear” on the headlights. Results are pretty good so far, I just need to test how long it will last.


What you need:
-800, 1000, 1500, 2000 grit wet/dry sandpaper
-Painters tape
-Some newspaper or plastic bags
-Denatured alcohol
-Tack Cloth
-Acrylic Lacquer
-PC7424 buffer*
-Compound*
-Polish*
-Sealant*
*Optional, if you don’t have a buffer, you can use your elbow grease and buff by hand with plastic-x or something similar.

Name: 05-15-2010_222.jpg
Views: 63
Size: 242.4 KB



1. Mask headlight to prevent any accidental contact with body. Take your time and try to get as close to the headlight as you can. I opened the hood so I wouldn’t have to worry about the hood. You can see how bad my headlights have become after a year without touching them.


Name: 05-15-2010_212.jpg
Views: 49
Size: 188.2 KB
Name: 05-15-2010_213.jpg
Views: 47
Size: 83.5 KB



Name: 05-15-2010_213.jpg
Views: 47
Size: 83.5 KB


2. Soak the various grades of sand paper in water. Sand headlights with 800grit in a horizontal and vertical motion. Do not go in circles.



3. Once complete and headlights look hazed, rise with water. It should look like this when dry.

Name: 05-15-2010_215.jpg
Views: 48
Size: 164.4 KB
Name: 05-15-2010_216.jpg
Views: 56
Size: 166.6 KB

4. Mask off the area around the headlight with your newspaper or plastic bags. Make sure you tape secure the tape down so the wind doesn’t fluff it around. I noticed that it was easier to tape when the body was wet. The plastic bags stuck to the body and allowed me to control my tape line with the plastic bag. Don't mind the paper towel, there was a hole and I didn't want to use another bag.

Name: 05-15-2010_217.jpg
Views: 47
Size: 200.2 KB


5. Prep the surface with a quick denatured alcohol wipe with a paper towel to make sure no other wax was left behind that you might have missed from sanding. Next take your tack cloth and gently wipe the surface to remove any dust that maybe stuck on the surface.

Name: 05-15-2010_218.jpg
Views: 43
Size: 166.5 KB


6. Now its time to spray your clear. I laid down the first two coats very lightly with 10 minutes in between coats. My third and fourth coat I was pretty heavy on. Make sure you cut into the corners and the bends on the lens and then spray horizontally across. What you want to do is make sure you have enough so you don’t sand it off in the next step.


Name: 05-15-2010_219.jpg
Views: 54
Size: 167.3 KB
Name: 05-15-2010_220.jpg
Views: 43
Size: 164.3 KB
7. Follow the drying times from the can. You will notice that it might have a milky color to it. Once dry it was clear.



8. You might notice that the surface is a bit rough. What you want to do is go through the sanding process again from 800 to 2000 but very lightly. You just want to make sure that the surface is smooth again.



9. Take your compound and buff the headlight so the haze is gone. Next, take your polish and buff the headlights. I opted to use a final polish to give it some more clarity. Finally I topped it off with my sealant. The sun went away when I took these pictures but you can see that they pretty much look new again


Name: 05-15-2010_227.jpg
Views: 47
Size: 132.5 KB
Name: 05-15-2010_225.jpg
Views: 42
Size: 122.0 KB
Name: 05-15-2010_224.jpg
Views: 48
Size: 140.4 KB

I should probably have not sealed it just so I can test it with it being exposed. This was done with readily available materials at parts stores. If you don’t own a buffer, you can use plastic-X and buff with your hand like some of you guys do. There was a slight breeze so when I was clearing I had to wait for it to stop. If you have a garage it should make this a lot easier to control. I am going to update this in a few months to see how it does. Enjoy!


i am thinking of doing my very soon. hope it help...
Attached Images
File Type: jpg 05-15-2010_213.jpg (83.5 KB, 8 views)
The Following User Says Thank You to sssmasss For This Useful Post:
TannerG (09-23-2011)
Old 09-23-2011, 01:53 PM
TannerG's Avatar
Registered User
iTrader: (1)
Join Date: Nov 2010
location: Olathe, Ks.
Posts: 878
Thanked 21 Times in 17 Posts
Good post. Have you noticed any chipping of the clear coat or anything?
Old 09-23-2011, 02:26 PM
Registered User
Join Date: Mar 2011
location: los angeles
Posts: 37
Thanked 1 Time in 1 Post
Thumbs up

good stuff
Old 09-23-2011, 03:35 PM
Registered User
iTrader: (2)
Join Date: Oct 2010
Posts: 116
Thanks: 0
Thanked 7 Times in 7 Posts
Keep updating on how this goes. My headlights have yellowed so bad. Im planning on doing the procedure of the sandpapers and just Plastic - X. See how long that lasts me. My car is normally garaged and rarely sits in the sun. So im hoping it last longer than a few months.
Old 09-25-2011, 01:36 AM
sssmasss's Avatar
Registered User
Thread Starter
Join Date: May 2011
Posts: 89
Thanks: 0
Thanked 6 Times in 4 Posts
it is perfectly fine for my. i had it done about 3 months now and everything work great..
Old 09-25-2011, 02:26 AM
Registered User
iTrader: (1)
Join Date: Aug 2011
Posts: 360
Thanked 15 Times in 9 Posts
i would have used UV clear coat
Old 09-25-2011, 04:56 PM
sssmasss's Avatar
Registered User
Thread Starter
Join Date: May 2011
Posts: 89
Thanks: 0
Thanked 6 Times in 4 Posts
yes i use clear lacquer that has anti uv.
Old 05-10-2014, 07:39 PM
Registered User
iTrader: (1)
Join Date: Jul 2008
location: Tempe, AZ
Posts: 221
Thanked 11 Times in 6 Posts
it's been three years now... how has the clear coat held up? i just restored my headlights again and you had posted in my thread hah
Old 08-09-2014, 01:39 AM
Registered User
iTrader: (2)
Join Date: May 2010
Posts: 1,112
Thanks: 0
Thanked 28 Times in 25 Posts
Im going to try this tomorrow. My headlights were not hazy or yellow just very scratched up with light scratches in certain areas. I did 1500 wetsand followed by 3k wetsand. Then scratch-x buff, polish, repeat. It got rid of most of the scratches and left the lights clearer overall but they are not crystal clear yet, still some light scratches seen. Im going to get the duplicolor clear coat uv protection kit to finish it up. Do I wetsand then apply for grip or do I apply it on the most clear product I can get with sanding and buffing. Also do I sand/ buff again after spraying clear? Thank you!
Old 08-10-2014, 12:41 AM
Registered User
iTrader: (22)
Join Date: Aug 2011
location: virginia beach
Posts: 6,869
Thanked 814 Times in 590 Posts


Gonna try this out. Wish me luck guys!
Old 08-10-2014, 06:13 AM
Registered User
iTrader: (1)
Join Date: Oct 2008
location: Chesapeake, VA
Posts: 492
Thanked 43 Times in 42 Posts
Good luck, let us know how it turns out.
Old 08-10-2014, 09:08 AM
Registered User
iTrader: (22)
Join Date: Aug 2011
location: virginia beach
Posts: 6,869
Thanked 814 Times in 590 Posts
Will post results.
Old 08-10-2014, 11:38 AM
Urbanengineer's Avatar
Registered User
iTrader: (2)
Join Date: Jun 2013
location: Pig Town, OHIO
Posts: 8,000
Thanked 632 Times in 598 Posts
Quote:
Originally Posted by Shane-O-Mac View Post
Will post results.
If you use a high speed random orbital buffer during the plastX stage you are going to love the results... Good luck.
Old 08-10-2014, 03:07 PM
Registered User
iTrader: (22)
Join Date: Aug 2011
location: virginia beach
Posts: 6,869
Thanked 814 Times in 590 Posts
I dident get any plastic x. Should I pick some up?
Old 08-12-2014, 11:26 AM
Registered User
iTrader: (1)
Join Date: Oct 2008
location: Chesapeake, VA
Posts: 492
Thanked 43 Times in 42 Posts
Quote:
Originally Posted by Shane-O-Mac View Post
I dident get any plastic x. Should I pick some up?
I think you are good to go. Your compound should be a little more abbressive than Plast X, and your polish is a little finer. Plast-X comes with a little bit of polymer protection/sealant built in, which you won't need since you are spraying.

I've used just Meg's Plast-X and a random orbital buffer in the past with excellent results.

Pretty much just Plastic X and follow up with some sealant looks pretty good, and looked about 90% like new. Doesn't last without some paint, though. Had to redo every 4-6 months.

You are on the right track.
The Following User Says Thank You to Hatchman For This Useful Post:
Urbanengineer (08-12-2014)

Related Topics
Thread Thread Starter Forum Replies Last Post
Detailing 19inch Rays! cmesidewayz Care & Detailing 1 09-29-2015 10:28 PM
FS[SoCal]: Injen Ses Exhaust dorkstar Engine - Exhaust 3 09-09-2015 08:43 PM
deal or no deal? TrillO.G.35 G35 Coupe V35 2003 - 07 14 09-05-2015 03:06 AM
FS: OEM Headlight bulb set Philips D2R johnadlertech Lights 0 09-04-2015 01:35 PM


Tags
applied, apply, clear, coat, cort, faded, head, headlight, headlights, lense, lenses, light, long, tinting, wait
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 07:55 AM.


Copyright ©2002 - 2017, rupromenergo.ru All Rights Reserved. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in:

Related pages


enkei 3 piece wheelswindshield fluid not coming outcarmax extended warrantyprocharger cog pulleyvortech supercharger frs 0 60smoked tail lightvossen wheels cv2which cassette adapter is bestblack work meisterclarion double din stereobest springs for koni yellowsterry saythermeister s1 replicacustom automatic shifter knobssilk road coilovershow to get rid of car door dings2003 cl600 0 60hardest hitting 12 inch subsscaring people with train hornhelmholtz calculatorinfiniti g37 brake padseclipse double din car stereowhat does whomp meanisimple tech supportq300 exhaustv36 sedanclutch and flywheel replacement costez pass exterior tagvis carbon fiber trunkq45 projector retrofitinfiniti coupesinfiniti vin decoderinfinity g37 horsepower8k or 10k hid2000 mustang saleen specswheel hub replacement costskyline australia forumpioneer 920bt2006 infiniti m35 mpgplasti dip starter kitcarbon fiber vinyl wrap interiorburning brake smellpump inertia2005 g35 sedan body kitinfiniti g35 upgradesinfiniti g35 2003 interiorg35 strutsnissan 350z stud patternjl audio capacitor2007 infiniti m35 interiornissan frontier o2 sensoreclipse double din car stereowire tuck engine bayair trapped in cooling systemsolar guard tint reviewg2 caliperpre oiler systemcraigslists san diego cars2007 infiniti g35xdiy radar jammercorbeau fx1 widehid flickeringairbags deployedac clutch replacement instructionsosram cbiracing seats with 5 point harnesswalboro 255 fuel pumpeline rotorste37 center caps2007 infiniti m35 interiorcar soap foamerkinetix high flow cats