DIY: K&N filter cleaning - new method - - Infiniti G35 & G37 Forum Discussion | rupromenergo.ru
Show Your Support Become A Premier Member

    > >
  • Reload this Page >
    • DIY: K&N filter cleaning - new method


DIY: K&N filter cleaning - new method

Thread Tools Rate Thread
Old 09-15-2006, 02:54 PM
Don't drink and Mag Race
Thread Starter
Join Date: Mar 2004
Posts: 2,065
Thanks: 0
Thanked 1 Time in 1 Post
DIY: K&N filter cleaning - new method

I saw this posted elsewhere, and it looked to be of use to all.

(NOT EDITED FOR SPELLING - YOUR MILEAGE MAY VARY)



Quoted below for the too-lazy-to-click crowd:


"this method is THE BEST BY FAR!!!!! it is EASY & FAST!!! & relatively CHEEP too!!!!


OK... i just figgered this out last weekend...arguably the BEST method i have EVER used to clean Cotton gauze air filter media....i have been cleaning these types of filtersd for about 20 years now & nothing REALLY seemed to CLEAN the stuff thoroughly......


This started because i have an SRT intake w/a AFE filter, & i was cleaning it the usual way: spray on the cleaner let it sit.. .rinse it out... blah blah... it seemed to work OK... but i could ALWAYS still see dirt & crap stuck into the filter media down deep in the grooves/pleats... this was pissing me off... so i cleaned it three times the last time ...
soak with filter cleaner..let sit, .rinse...
soak again w simple green, let sit in the HOT sun...& rinse...
then AGAIN, soak with with orange glow cleaner & simple green then let sit & rinse....

STILL there was dirt & bug parts & oil grime down in the pleats & even at the ends of the outside pleats..... WTF!! & you DO NOT want to blast it from the inside with a water or air hose.. .you will damage the cotton that needs to stay in good shape to filter properly....


Then..I had an idea......


I got a small bucket... dumped two scoops of that Oxy clean crap /powder in it & then placed the filter in there.....next i poured 1 1/2 $1.39 2 liter bottles of generic CLUB SODA in the bucket.....(about 3 litres total...dep on the bucket you use...use a smaller one to use less Club Soda etc...)

WELL!!! that **** bubbled & foamed up almost Instantly & this greasy dirty film & TONS of dirt & crap just freaking JUMPED out of the filter gauze!!!!! the foam was all topped with this yellow filter oil & dirt & grime & bug detritus .. .it was amazing that all this crap was STILL in there after cleaning it traditionally 3 times..... the Club Soda was the trick for SURE the carbonation in that just 'boiled' the crap out of the cotton gauze fibers instantly...!!

SOO much crap came out i ended up using a piece of paper to scoop the nasty oily grime & dirt & such that was riding on top of the foam in the bucket out & dumped it so i would not have to lift the filter up & out thru that ****.... i swirled the filter around in the solution for about 3- 4 minutes & then let it sit for a minute or three.....finally I just shook it in the solution for a few seconds & pulled it out... OMG.. .it was CLEANER than NEW!!! I mean it was SPARLKING clean!!!! elapsed time: 10 minutes MAX!!

ALSO....this is VERY gentle on your filter media.. .(cotton gauze) & is MUCH better than blasting it with water & or air trying to rinse out the crap or blow it out all of which are highly discouraged by the filter makers....

let it dry properly, (Note without all that residual grease & grime still clogging the filter.. .it WILL DRY MUCH FASTER !) then oil it up & reinstall.... i actually have two filters so i do not have to wait on drying & oiling the filter to drive my car when cleaning filters i just keep one all oiled & clean & ready then i can take my time cleaning drying & oiling up the other one....

you can use ANY cleaning degreasing solution I would imagine...it was the Club soda not the 'Oxy clean' that made the HUGE difference.. but feel free to copy this method to a 'T' if you want to...."
Old 09-15-2006, 03:02 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Join Date: May 2005
location: ɐʍ 'ǝlʇʇɐǝs
Posts: 35,467
Thanked 523 Times in 438 Posts
Doesn't the OXY bleach the cotton?
Old 09-15-2006, 03:55 PM
JgY JgY is offline
Registered User
Join Date: Sep 2006
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks for the post. This info will definitely come in handy for me.
Old 09-15-2006, 04:20 PM
Registered User
iTrader: (1)
Join Date: Apr 2006
location: Kansas City
Posts: 1,111
Thanks: 0
Thanked 0 Times in 0 Posts
i dont think the OXY bleaches anything. Ive never used oxyclean but from what i remember on the commercials he put scoops of oxyclean in a tub of colored clothes also...i remember seeing a red shirt...cant truely confirm this...
Old 09-15-2006, 05:09 PM
Registered User
iTrader: (1)
Join Date: Nov 2004
Posts: 412
Thanked 0 Times in 0 Posts
I've read thousands of times that the dirt buildup actually helps the filtering process. I've always cleaned my filters gently, and they always look a lil dirty.
Old 09-15-2006, 05:35 PM
Registered User
iTrader: (3)
Join Date: Dec 2004
location: Boston, MA
Posts: 3,632
Thanks: 0
Thanked 12 Times in 4 Posts
interesting read....oxy clean doesnt contain bleach btw

think this would work on a non oil filter?
Old 09-15-2006, 08:33 PM
O.F. Administrator
iTrader: (4)
Join Date: Jun 2002
location: Cambridge, Ont. Canada
Posts: 30,341
Thanks: 0
Thanked 7 Times in 5 Posts
TNX, ChicagoX....I've transfered a copy to our DIY forum.....

C.
Old 10-21-2006, 08:58 PM
O HELLA JDM's Avatar
Registered User
iTrader: (49)
Join Date: May 2006
location: San Diego, CA
Posts: 18,874
Thanked 22 Times in 18 Posts
this question might be off topic...or on topic...is this better than using a filter cleaner...or like a K&N recharger kit or what ever....just wondering
Old 10-25-2006, 11:33 AM
chobble19's Avatar
Registered User
iTrader: (56)
Join Date: Apr 2006
location: MIAMI
Posts: 3,394
Thanked 4 Times in 4 Posts
can this method be used with injen cold air filters as well?


Quote:
Originally Posted by ChicagoX
I saw this posted elsewhere, and it looked to be of use to all.

(NOT EDITED FOR SPELLING - YOUR MILEAGE MAY VARY)



Quoted below for the too-lazy-to-click crowd:


"this method is THE BEST BY FAR!!!!! it is EASY & FAST!!! & relatively CHEEP too!!!!


OK... i just figgered this out last weekend...arguably the BEST method i have EVER used to clean Cotton gauze air filter media....i have been cleaning these types of filtersd for about 20 years now & nothing REALLY seemed to CLEAN the stuff thoroughly......


This started because i have an SRT intake w/a AFE filter, & i was cleaning it the usual way: spray on the cleaner let it sit.. .rinse it out... blah blah... it seemed to work OK... but i could ALWAYS still see dirt & crap stuck into the filter media down deep in the grooves/pleats... this was pissing me off... so i cleaned it three times the last time ...
soak with filter cleaner..let sit, .rinse...
soak again w simple green, let sit in the HOT sun...& rinse...
then AGAIN, soak with with orange glow cleaner & simple green then let sit & rinse....

STILL there was dirt & bug parts & oil grime down in the pleats & even at the ends of the outside pleats..... WTF!! & you DO NOT want to blast it from the inside with a water or air hose.. .you will damage the cotton that needs to stay in good shape to filter properly....


Then..I had an idea......


I got a small bucket... dumped two scoops of that Oxy clean crap /powder in it & then placed the filter in there.....next i poured 1 1/2 $1.39 2 liter bottles of generic CLUB SODA in the bucket.....(about 3 litres total...dep on the bucket you use...use a smaller one to use less Club Soda etc...)

WELL!!! that **** bubbled & foamed up almost Instantly & this greasy dirty film & TONS of dirt & crap just freaking JUMPED out of the filter gauze!!!!! the foam was all topped with this yellow filter oil & dirt & grime & bug detritus .. .it was amazing that all this crap was STILL in there after cleaning it traditionally 3 times..... the Club Soda was the trick for SURE the carbonation in that just 'boiled' the crap out of the cotton gauze fibers instantly...!!

SOO much crap came out i ended up using a piece of paper to scoop the nasty oily grime & dirt & such that was riding on top of the foam in the bucket out & dumped it so i would not have to lift the filter up & out thru that ****.... i swirled the filter around in the solution for about 3- 4 minutes & then let it sit for a minute or three.....finally I just shook it in the solution for a few seconds & pulled it out... OMG.. .it was CLEANER than NEW!!! I mean it was SPARLKING clean!!!! elapsed time: 10 minutes MAX!!

ALSO....this is VERY gentle on your filter media.. .(cotton gauze) & is MUCH better than blasting it with water & or air trying to rinse out the crap or blow it out all of which are highly discouraged by the filter makers....

let it dry properly, (Note without all that residual grease & grime still clogging the filter.. .it WILL DRY MUCH FASTER !) then oil it up & reinstall.... i actually have two filters so i do not have to wait on drying & oiling the filter to drive my car when cleaning filters i just keep one all oiled & clean & ready then i can take my time cleaning drying & oiling up the other one....

you can use ANY cleaning degreasing solution I would imagine...it was the Club soda not the 'Oxy clean' that made the HUGE difference.. but feel free to copy this method to a 'T' if you want to...."
Old 11-03-2006, 08:15 PM
NismoV35's Avatar
Registered User
iTrader: (1)
Join Date: Feb 2003
location: Los Angeles, National Socialist Democratic Republic of Facistfornia
Posts: 2,458
Thanks: 0
Thanked 0 Times in 0 Posts
Uh Get the New AEM "Dry Flow" Air filter Never Needs Oiling
Old 11-03-2006, 11:31 PM
Registered User
iTrader: (1)
Join Date: Apr 2005
location: Carteret, NJ
Posts: 3,395
Thanks: 0
Thanked 16 Times in 6 Posts
What would happen if i was to clean my Injen filter, but then not oil it because I ran out of it ?
Old 11-13-2006, 09:05 PM
Registered User
Join Date: Jan 2004
location: Aurora, CO
Posts: 83
Thanks: 0
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by chilibowl
What would happen if i was to clean my Injen filter, but then not oil it because I ran out of it ?
You need to oil the outside of the filter. Without it, the filter would not be as efficient in trapping dirt and other contaminants.
Old 11-13-2006, 09:06 PM
Jeff92se's Avatar
Red Card Crew
iTrader: (24)
Join Date: May 2005
location: ɐʍ 'ǝlʇʇɐǝs
Posts: 35,467
Thanked 523 Times in 438 Posts
True. But you have to end up buying a new one every time.

Quote:
Originally Posted by NismoV35
Uh Get the New AEM "Dry Flow" Air filter Never Needs Oiling
Old 12-14-2006, 11:05 AM
Registered User
Join Date: Jul 2006
location: Sunny CA
Posts: 734
Thanks: 0
Thanked 0 Times in 0 Posts
Quote:
Originally Posted by Jeff92se
True. But you have to end up buying a new one every time.
Not really, a long life filter. You still wash them out with their cleaner, but don't oil them.
Problem is the AEM only comes in cone styles.

For factory use the Amsoil nanofiber filter. You clean it with low pressure shop air every 10K or so. That's all. No oil. I think it's good for 50K miles.

Number for the G35 is EAA74.
Old 12-23-2006, 08:07 PM
codeflux's Avatar
Registered User
iTrader: (26)
Join Date: May 2004
location: San Francisco, CA
Posts: 4,105
Thanked 4 Times in 4 Posts
/me goes off to buy some oxiclean and club soda. my pop-charger is filthy!

Related Topics
Thread Thread Starter Forum Replies Last Post
FS: FOR SALE: 2004 G35X Sedan in Maryland NailBomb G35 Cars 2 10-28-2015 08:53 AM
Detailing 19inch Rays! cmesidewayz Care & Detailing 1 09-29-2015 10:28 PM
I did it! TNRocker New Members Check In 6 09-21-2015 09:36 AM
2 Air Filters (Pronto) - Free ben_m Engine - Intake/Fuel 0 09-07-2015 11:04 PM
FS: Z Tube + JWT Popcharger w/ K&N Filter Recharge Kit JG_G35 Engine - Intake/Fuel 2 09-07-2015 10:35 PM


Tags
air, alternative, clean, cleaning, dirty, diy, filter, filters, green, homemade, intake, kn, methods, oil, simple, solution
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 11:25 PM.


Copyright ©2002 - 2017, rupromenergo.ru All Rights Reserved. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Related pages


skunk2 suspension reviewsadjusting tein coiloversmaf sensor testinghow to replace rear bearingscatalytic converter california lawphilips d2rbleed screw for radiatorwet sand headlight restorationwhat side is bank 2 sensor 2legacy infinitihow to install throttle body spacernissan 350z single exhaustboss rear view camerafuel sensor replacement costcoolant funnelg35 rear spoilerrx7 clutch kit350z exhaust tipsstruts vs shockscustom coolant reservoirg35 air intakepursuit remote start2003 infiniti g35 steering wheelsoundgate m2vortech supercharger v2streets of willow track day350z hotchkis sway barsfosgate p1000axxess steering wheel control interfacerb26dett front clipbridgestone potenza re760 reviewpac steering wheel controlsrockford fosgate power t5002costco ameriprise car insurance reviewgas gauge going up and downinfiniti g37s ipl2006 g35 coupe weightsinnistar passwordxxr 526 whiteracing seats for 350zfrys in natomasbeshoff infinitytapping noise engineaudioque 1200dwhat does vdc meanheadlight and taillight tint lawswheel spacers with extended studswheel hub assembly symptomscarport costcocenter caps for rims aftermarketwindow tinting halifax99 saturn sl2memphis belle speakersbc coilovers rsxcar brake lights wont turn offwhy does my car shake when i apply the brakeshow to install a turbo timerg35 sedan mpginfiniti g37 coupe 2006symptoms of a bad camshaft sensorascd switchplasti dip cansdo radar detectors really workhub bearing pullerinfinity gx37zapco dc360 4zymol concours reviewidler pulley bearingsscion frs sedancostco newmarket phone numberr1 concepts reviewwhere is the tail light fusecar code p0420varrstoen es1 goldag wheels m510chikara wheels