Replacing the spark plug well seals in the valve covers - - Infiniti G35 & G37 Forum Discussion | rupromenergo.ru
Show Your Support Become A Premier Member

    > >
  • Reload this Page >
    • Replacing the spark plug well seals in the valve covers


Replacing the spark plug well seals in the valve covers

Thread Tools Rate Thread
Old 05-09-2011, 02:06 PM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
Replacing the spark plug well seals in the valve covers

Name: 101_0937.jpg
Views: 1510
Size: 62.0 KB

The above picture was my reasoning for tackling this job. As you can see in the post, my spark plug electrode is worn down and the plug is bathed in oil. I had this problem on my rear passenger side plug and on my front-most driver side plug. There are two ways to solve this problem. Replace the seals with the kit from R&D Factory or replace the valve covers with new ones. The new covers are about $180 each. I chose the R&D route. R&D kit offers the kit with the following pricing structure.
60 for 6 orings
90 including oem valve cover gaskets(both side)
100 including oem pcv valve and the gasket.

The Installation is extremely straightforward and I followed the


It's necessary to print the intake manifold collector and rocker cover section from the factory service manual in the Engine Mechanical section. These sections give you torque values and bolt removal and re installation order. I also used the instructions on this to Reset my ECU, and reset my idle (I removed and cleaned my throttle body). Swivel sockets help, torque wrenches for inch-lbs and foot-lbs are absolutely necessary. Also needed is a hole saw size 1-7/8 which I got from my local ACE Hardware in Bridgeport, CT and black RTV silicone which you can get anywhere. Set aside 4 hours if this is your first time.

Remove the manifolds and covers.

Name: 101_0933.jpg
Views: 2622
Size: 127.9 KB

Name: 101_0939.jpg
Views: 1778
Size: 143.3 KB


You must drill concentric holes are the plug tubes. Notice my middle one isn't. Don't do that!
Name: 101_0940.jpg
Views: 1624
Size: 91.2 KB


You can then put rtv on the underside of the new seals and the pop right into position.
Name: 101_0943.jpg
Views: 1527
Size: 94.8 KB


If you remove your throttle body and unplug it to clean it, your ecu will hate you and your warm idle will sit 1150. I resolved the problem by letting the car cool down, then I did ECU reset, accelerator Pedal realease position procedure, then Throttle valve closed position and lastly I warmed up the car to do Idle Air volume learning. Some other pics from the job are below!

If you have never used a hole saw before, practice on something first!

Name: 101_0920.jpg
Views: 1346
Size: 94.8 KB

Name: 101_0922.jpg
Views: 1360
Size: 118.2 KB

Name: 101_0926.jpg
Views: 1384
Size: 119.3 KB

Name: 101_0931.jpg
Views: 1339
Size: 114.5 KB

Name: 101_0936.jpg
Views: 1347
Size: 131.1 KB

Name: 101_0938.jpg
Views: 1355
Size: 145.1 KB
The Following 4 Users Say Thank You to onthe3rdday For This Useful Post:
avavpez1 (07-15-2013), Blue Dream (06-09-2011), Drifter2090 (03-14-2014), S 854 (08-27-2011)
Old 05-10-2011, 10:34 PM
Texasscout's Avatar
Registered User
iTrader: (11)
Join Date: Feb 2005
location: South Texas
Posts: 27,164
Thanked 1,435 Times in 1,125 Posts
I'm a little lost here. Why did you need a hole saw? What were the "O" rings? Just plain O-rings or were they square profile seals that are round like an o-ring?
Old 05-10-2011, 11:07 PM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
I needed a hole saw because the valve covers are plastic and the spark plug tube seals are inaccessible. You have to drill out the plastic around the seals to pull it out. With the kit from R&D Factory the o-rings are round and the "pop" into position just like traditional spark plug seals
Old 05-14-2011, 09:31 PM
Texasscout's Avatar
Registered User
iTrader: (11)
Join Date: Feb 2005
location: South Texas
Posts: 27,164
Thanked 1,435 Times in 1,125 Posts
I asked about the oring because of the prices you posted. $60 of SIX ORINGS? That's nutz. Even if they were Viton (tm) (up to 400 degF), the cost of the rings is only pennies each. If they are of a common size (even metric), not proprietary, you can buy them at most any "Seal and Gasket" shop for less than a dollar each. You would just need to size them. The only elastomer that would be more expencive would be Aflas (tm) or Kalrez (tm). Both of those will handle up to 500 degrees.

All those elastomers and many other were invented by DuPont.

Last edited by Texasscout; 05-14-2011 at 09:37 PM.
Old 05-15-2011, 12:59 AM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
Agreed that 60 bucks for o-rings is like paying $60 for shoe laces, however, I am not knowledgeable enough on the subject to find the product I needed. Kudos to r&d factory! At the end of the day, replacing o-rings in valve covers designed like ours is time consuming. A more traditional metal cover with shelf stock o-rings would be ideal.
Old 05-16-2011, 12:16 AM
Registered User
iTrader: (5)
Join Date: Feb 2008
location: DFW TX
Posts: 216
Thanked 8 Times in 8 Posts
onthe3rdday, i know you only posted this 6 days ago but maybe on you next oil change can you give us an update on how the new seal are holding up?
Old 05-16-2011, 02:00 AM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
Sure will, I got 1K miles on the car since that job
Old 05-22-2011, 08:41 PM
Registered User
Join Date: Aug 2010
location: Tampa, FL
Posts: 64
Thanks: 0
Thanked 1 Time in 1 Post
I just did my driver's side yesterday. still have to do the pass side. didn't want to put it back together half done but its my only drivable car, currently, and I had plans for the evening.
Anyway, anyone who is interested in tackling this, I made a bushing to center the hole saw over the plug holes...it worked great!! pm me if you happen to be interested in this.
Old 05-22-2011, 09:42 PM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
A bushing to center the hole....nice! Taking off the manifold to do this twice= you are a beast. Admittedly I had to take mine down twice, but rfor another reason.
Old 05-22-2011, 10:28 PM
Registered User
Join Date: Aug 2010
location: Tampa, FL
Posts: 64
Thanks: 0
Thanked 1 Time in 1 Post
lol. taking off the manifold is the easy part. looks like getting the pass side valve cover off is gonna be a pain! I had thought maybe I could do some port work to the manifold while I had it off but, it doesn't look like there's much to be done in there! It all looks pretty good (aside from needing a good cleaning).
Old 05-23-2011, 12:26 AM
Registered User
Thread Starter
iTrader: (5)
Join Date: Mar 2010
location: Bridgeport CT
Posts: 298
Thanked 16 Times in 7 Posts
Passenger side is a BITCH. No if's and or buts about it. Enjoy! Something tells me you'll be fine.
Old 06-05-2011, 09:07 PM
Registered User
Join Date: Aug 2010
location: Tampa, FL
Posts: 64
Thanks: 0
Thanked 1 Time in 1 Post
its all done. has been for about two weeks now. so far, so good. the pass side wasn't as bad as I thought it might be.
Old 06-07-2011, 09:26 PM
Registered User
Join Date: Feb 2009
location: Atlanta, GA
Posts: 14
Thanks: 0
Thanked 1 Time in 1 Post
onthe3rd,

Just ordered my seals, 5th spark plug tube is leaking. I figured I would do this fix since I am putting the mrev2 in. How is everything holding up so far since you did this?
Old 06-07-2011, 09:37 PM
Registered User
Join Date: Aug 2010
location: Tampa, FL
Posts: 64
Thanks: 0
Thanked 1 Time in 1 Post
its holding up good as far as I can tell, so far. If you want a bushing to center your hole saw, let me know. It made the job way easier than it would have been without it!! Also, the baffles didn't come out of my valve covers by keeping the hole saw so well centered. You just have to be more clean this way...keep the plastic shaving from getting under (over) the baffle.

-Alan
Old 06-07-2011, 10:44 PM
Registered User
Join Date: Feb 2009
location: Atlanta, GA
Posts: 14
Thanks: 0
Thanked 1 Time in 1 Post
Not sure if I completely understand. Aren't the baffles molded to the valve covers anyways, preventing them from coming out?

How did you keep the shavings from getting behind the baffle? And is your way messier than without the bushing?

All in all, I would want a bushing to center the saw to make the job easier.

Related Topics
Thread Thread Starter Forum Replies Last Post
New to the G family, I Need help Terry_G35 New Members Check In 14 08-20-2015 10:56 PM
FS: 05 G35X sedan $6700 wuppiedog G35 Cars 1 08-07-2015 12:16 PM
06 6mt coupe misfiring 😓 ghost_g35 Engine, Drivetrain & Forced-Induction 2 08-07-2015 11:31 AM
2003 G coupe. Need help guys please Terry_G35 G35 Coupe V35 2003 - 07 8 08-04-2015 03:38 PM
Oil Catch Can confusion lemmy999 G35 Sedan V35 2003-06 0 07-25-2015 01:13 PM


Tags
203, 350z, cost, cover, covers, g35, hole, infiniti, mazda, plug, replace, rtv, seal, sealers, seals, spark, tube, valve, video
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 08:56 PM.


Copyright ©2002 - 2017, rupromenergo.ru All Rights Reserved. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in:

Related pages


g35 injen intakesupercharger whinebonedaddys arlington txstrut bars vs sway barskicker l7 subwooferg37 engineinfiniti etobicokekijiji infiniti g35bully dog gt tuner 40410350z stage 1kinetix racingfom usainstalling line out convertergalant vr4 forumvarrstoen es7 17x9diy power brake bleederempty radiator reservoiriforged.comhow to stop rod knockvarrosteonsecond skin audio coupon coded51r optimaactivating xm radiousa spec pa15-infifiberglass subwooferg35 warrantyjl audio w6 priceg35 throttle bodybauer supreme one90tensioner pulley boltavh x5600bhs reviewhow to make your car backfiretemporary car taghow to properly paint rimsvht night shadenissan long life coolantelectric supercharger for salemy car shakes when i turn it once28n genesisnokian entyre forumsbmw 550i vs 335itwincharger kit for salesuperbrightled.comakebono vs ebcball joint tool autozonesebring exhaustsoundstream reference 500how to clean akn air filterinfiniti g35 or nissan 350zkobalt floor jackhrspringsprincess auto flyer edmontonturbo whistlersdoes dr colorchip workriding the clutch on a hilljl 10w6v3infiniti maintenance schedule g37putting water in radiatorinfiniti ray catena edison njbc racing coiloverg35 steering wheelcigarette lighter aux cordpassport infinitblack magic tintg37 coupe mods2004 g35 headlight bulb replacementinfinity gx372003 wrx 0-60clear coat perimeter mallbypass valve superchargerpioneer avic 920btg35 stickers