My SPC A-Arm installation - - Infiniti G35 & G37 Forum Discussion | rupromenergo.ru
Show Your Support Become A Premier Member

    > >
  • Reload this Page >
    • My SPC A-Arm installation


My SPC A-Arm installation

Thread Tools Rate Thread
Old 10-11-2006, 12:57 AM
Registered User
Thread Starter
iTrader: (7)
Join Date: Apr 2004
location: Orlando, FL
Posts: 8,001
Thanked 6 Times in 5 Posts
My SPC A-Arm installation

I was fortunate enough to get the first SPC A-Arm set in Florida from IAPdirect.com for testing on my 2004 G35 coupe. I finally met Peter, the owner of IAP, and he's a really nice guy with a clean operation.

The A-Arms were part of a project to swap out the springs (350Z S-Techs), shocks (Tokico D-specs), brake lines (Goodrich stainless), brake rotors (Fast Brakes custom drilled/slotted rotors, 15.2 front, 13 (stock size) in rear w/ caliper spacing bracket for the Brembos), SPC camber arms, and SPC toe bolts. So some of the pics will show some of those parts being replaced too.

The design of the SPC A-Arms allow more positive camber adjustment than with probably all of the A-Arm kits out there due to the inclusion of hub spacers in the kit that go between the steering knuckle and the hub. My drop on the S-Techs isn't severe enough to require the spacers. The A-Arms gave enough adjustability.

I forgot to weigh the SPC A-arm to compare them with stock..

Also, the SPC units allow adjustment of the caster of the car using a notched cam type of spacer, but I left them at zero caster.

OK, now for the install: You need 14mm socket, 17mm socket, and a 27mm socket (for the adjusting nut). A 1 1/8 inch socket or wrench will also work for the adjusting nut. Keep in mind that this unit is an initial production sample. Peter assured me that the production units will be finished better. We installed them in my garage and needed no special tools, except for the spring compressor, which wasn't entirely necessary.

The install was pretty simple and could be done within a couple of hours or so.

First some pics of the kit.

































After you remove the wheel, remove the cotter pin holding the stock a-arm bolt onto the steering knuckle. It's 17 mm. I was doing a brake rotor upgrade so I went ahead and removed the rotors and calipers at the same time.





The threaded shaft spun on the A-arm as we tried to remove the nut, but we were able to remove the nut once we got the other two bolts holding the A-arm to the chassis out, spun the A-arm around, and pushed down on it to apply pressure to the shreaded shaft that the nut is on.

However, before we could swing the A-arm around to apply pressure to the threaded shaft and remove the nut, we had to remove the bolts holding the A-arm to the body. The rearward bolt (14mm) came out easily, but the front bolt doesn't have enough room to com all the way out because of the position of the shock. We used a spring compressor to drop the shock down to shift the shock over slightly to give enough room to remove the bolt.

On the other side, we simply slid down the boot on the boot on the OEM shock to allow enough room to slide that front bolt out of the way.

We have since done another A-arm swap on roncfpz's 350Z with Tein CS coilovers. We simply removed the three nuts holding the coilovers to the strut tower, dropped the coilovers a little toward the back of the car, and removed the frontmost bolt. We reversed the procedure to reinstall the A-arms. This should work for stock shocks too.



This pic shows us applying pressure to the A-arm to remove the nut.


Next, we oriented the caster to 0 and tightened it down with a 27 millimeter socket before mounting the A-arm. Double check that you have the caster cam (?) oriented correctly before installing the A-arm. I had to go back and set both sides to zero caster after they were on the car, BUT, it's really easy to change caster once the A-arms are on the car. Just remove the 17mm nut, swing the A-arm down, and correct it.





Next, cut the wires holding the two roller bearings into the SPC A-arm assemblies where they mount to the car body. Be careful, the bushings will slide out. It also took a little rubber hammering to get those bushingsto fit into the mount location of the strut tower. Insert the 14 mm bolts and tighten.

Lastly, insert the new conical bushing in the SPC kit where the steering knuckle goes onto the A-arm. Then, put the new 14 mm nut onto the threaded shaft (red rubber boot) and tighten it. Reinsert the new cotter pin that is supplied in the kit. The photos show the wide range of motion of the shaft beneath the red rubber boot.















The Following User Says Thank You to Gilley For This Useful Post:
laksjd84 (06-10-2011)
Old 10-11-2006, 12:58 AM
Registered User
Thread Starter
iTrader: (7)
Join Date: Apr 2004
location: Orlando, FL
Posts: 8,001
Thanked 6 Times in 5 Posts
Finally, the finished product.






I have had the A-arms on the car for about 5 weeks now. They have been to the alignment shop and the alignment guy had no problem adjusting them to get the alignment within spec. They have over 2500 miles on them now and I have had no issues with them. They don't make any noise, like some do. They are easy to install and they are a well built product. They do weigh more than stock, but all aftermarket A-arms will likely weigh more than the stock aluminum units. For those the want to adjust caster or that have extreme drops, these are the only choice on the market right now.

I didn't install the shims between the hub and the steering knuckle. It will take more effort to install those shims, but if you need the extra positive camber, the shims will provide it to you.

Thanks to my buddies from the Florida G35 Club who came to my house and helped with all the parts installation - Chuck, Ian, Shermie, Jose, Ryan, and my brother, Wade.
Old 10-11-2006, 08:34 AM
cato's Avatar
SouthernComfort Moderator
iTrader: (7)
Join Date: May 2003
location: Sugar Land,Texas
Posts: 3,653
Thanks: 0
Thanked 4 Times in 4 Posts
Looks great. Time to replace those stock sway bars!
Old 10-11-2006, 11:58 AM
Registered User
Thread Starter
iTrader: (7)
Join Date: Apr 2004
location: Orlando, FL
Posts: 8,001
Thanked 6 Times in 5 Posts
Quote:
Originally Posted by cato
Looks great. Time to replace those stock sway bars!
Thanks. Already done with the new Hotchkis design. I had planned to put them on at the same time, but they didn't arrive in time.
Old 10-11-2006, 12:17 PM
Demonteverde's Avatar
Moderator
iTrader: (4)
Join Date: Feb 2004
location: Orlando, FL
Posts: 2,766
Thanked 8 Times in 6 Posts
That was a very good write up, Sean. Thanks for making this...

Anyone reading this who are interested in the SPC camber kits, Peter at is the guy to contact...
Old 10-11-2006, 01:47 PM
IAPDirect.com's Avatar
Registered User
iTrader: (4)
Join Date: Jul 2005
location: Where East Meets West
Posts: 230
Thanks: 0
Thanked 0 Times in 0 Posts
Nice Writeup Sean! Thank you for your help.


Ian, thanks for the post!

The kits will be here this Friday!! Only a handful of these left with no current ETA on the next batch.

Take care guys.
Old 10-11-2006, 02:19 PM
_jb's Avatar
_jb _jb is offline
Photographer
Join Date: Nov 2002
location: St.Pete, FL
Posts: 5,050
Thanks: 0
Thanked 0 Times in 0 Posts
Great pictures, writeup, and tutorial, Sean!

Your detailed instructions and pictures could probably substitute for an installation manual.

I was especially interested in how SPC was going to provide caster adjustability with only a single adjustment bolt. Your pictures and writeup clearly explain that. Quite an ingenious method.

Can we make this a Sticky?

Related Topics
Thread Thread Starter Forum Replies Last Post
FS: G35 coupe sport side skirts R350k5 Exterior - Body Parts 10 10-01-2015 09:41 PM
anyone have issues with powerslot rotors? 3000vr4tt Brakes & Suspension 3 09-07-2015 01:48 AM
FS: UTEC Engine Management System SilverG123 Engine - Electrical 1 09-04-2015 02:12 PM


Tags
2002, aarms, adjustment, arm, arms, bolts, camcaster, f150, rupromenergo.ru, good, install, installation, instructions, positive, review, spc
Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 07:04 AM.


Copyright ©2002 - 2017, rupromenergo.ru All Rights Reserved. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Related pages


infinity kappa 52.9iinfiniti g37 replacementhow to use engine restoremobile 1 vs castrolenkei pk6momo shifter knobrockford polisher bufferg35 coupe parts for salefunction form coilovershornblaster train horn kitdunlop winter sport m3 reviewhow to activate xm radiobrake pads infiniti g352001 nissan pathfinder coil packmemphis 16-mc1000dvancouver beef jerky04 g35 headlightsinfinity kappa perfect 12tiki toms2004 infiniti g37 coupecam cover gasket oil leaksparco chrono seatsinfiniti boston area2006 honda accord wiper blade sizepioneer avh-x5600bhsm35 gas mileagelexani lx seven reviewklass wheelstcw3 oildrive shaft pulleyhow much does a crankshaft position sensor cost350 z rimsmiami dade window tintingautozone service engine soonreplace door lock actuatorlexus gs400 exhaustls1 engine cost350z hr turboinfiniti g37s horsepowerwork wheels vsxxair spencer cs-x3volk gt7satin black paint job priceebay spoilerphilips germany d2s 35w 85122dr colorchipelectric clutch fanmtx 600xdrsx type s reliabilitydeepest concave wheelsbbs lemans replicapioneer avic z2 bluetooth adapterinfiniti g25 problemsvossen cv2maaco riprocharger kansas cityauto couture wheels for saleleft outer tie rod endmolykote m77purolator gold oil filterinfiniti g2vortech installationkenwood ddx470buying an rx8does autozone check engine codes for freeupper radiator hose hotinfinity g35x 2007ford racing fr500 wheelshow to prep aluminum wheels for painthow to burnout in manualk&n filter installationjdm steering wheelsforgestar f14 super deep concave for sale